Entreposage & Hivernisation

 

Performance Voyer possède l'une des meilleure installation d'entreposage intérieur et extérieur. Soyez tranquille en sachant que votre bateau, moto ou VTT est à l'abri des éléments tout au long de l'hiver.

Tous les bateaux hivernisés et/ou stocké avec Performance Voyer passe par une liste de contrôle à l'arrivée et au départ pour s'assurer que tout, de la proue à la poupe, a été inspecté et est en bon état de fonctionnement.

🛥️ Service d’entreposage & hivernisation

Prenez soin de votre embarcation hors saison

Pendant l’hiver, confiez-nous votre bateau — on s’en occupe comme si c’était le nôtre. Entretien, protection, inspection : tout est pris en charge.

👉 Contactez-nous pour réserver votre place


🧼 Lavage de coque à l’arrivée

Dès son arrivée, votre embarcation est nettoyée avec des produits marins haut de gamme.
✅ Coque et quilles propres
✅ Fait avec soin par notre équipe


❄️ Hivernisation complète

Protégez votre moteur et vos systèmes du froid :

  • Vidange & changement d’huile (moteur, transmission, pied)

  • Stabilisateur d’essence

  • Antigel dans tous les circuits (vivier inclus)

  • Vérification batterie et composantes clés

  • Inspection moteur, hélice, embrayage

💡 Même peu utilisé, un moteur reste exposé à l’humidité — l’hivernisation est essentielle.


🏠 Options d’entreposage

🧊 Intérieur
✔ À l’abri des intempéries
✔ Entrepôt ventilé et sécurisé
✔ Prêt à repartir dès le printemps

🌨️ Extérieur
✔ Enveloppé dans une pellicule protectrice
✔ Absorbeurs d’humidité inclus
✔ Espace clôturé et surveillé


🚚 Transport clé en main

On vient chercher votre embarcation et on vous la rapporte au printemps.
Aucune logistique à gérer — on s’en occupe.

👉 Demandez votre soumission maintenant


🌞 Préparation au printemps

Réservez votre remise en marche (délai de 7 à 14 jours) :

  • Test système de charge & pompes

  • Analyse des huiles

  • Graissage & ajustements

  • Vérification complète de la remorque


🧽 Lavage intérieur (optionnel)

Offrez-lui un nettoyage complet avant son retour à l’eau :
✅ Plancher
✅ Sièges
✅ Console & cockpit


📞 Contactez-nous pour un service sur mesure
Profitez de la saison froide pour faire inspecter, réparer ou entretenir votre embarcation.

 

Stock #  340-1201

SPX EXTERNAL MODEL-ADHESIVE HEATED GRIP KIT (12-170)

Dealer Price $76.95 CAD
Overview

SPX EXTERNAL MODEL-ADHESIVE HEATED GRIP KIT

  • STEP 1 Remove grips. If you have rubber grips, heat them until they become flexible. Break the mastic by inserting a Phillips screw-driver between grip and handlebar. Then pry grip straight off. Do not attempt to twist off grip
  • STEP 2 Remove all residue (glue, rubber, etc..) from area covered by grip on handlebar. Clean properly using either fine sandpaper or gasoline to obtain a residue free surface, ready to receive the heating element.
  • STEP 3 Remove white contact protector from heating element. Encircle cleaned area with heating element, replace rubber grip on each side Attach wires along control wire to pass underneath the hood
  • STEP 4 Drill a 1/2
  • STEP 5 Take the wire from the heating element which is not connected to the switch and attach it to a suitable ground.
  • a) Electric Start Models: Take a length of 18 gauge stranded wire & connect it to the end of the single wire which extends from the Y junction & connect it to the accessory lug on the rear of the snowmobile ignition switch
  • b) Manual Start Models: The wire mentioned in
  • STEP 6 Choose the switch position for the desired function: 1) Up position for high heat 2) Centre off: 3) Down position for low heat. NOTE: The lead on which the resistor is installed should be connected to the terminal which is located in front of the slot on the threaded portion of the switch in order to match the HI-OFF-LO switch.
  • STEP 7 Fasten wiring to steering column with electrical tape or a nylon tie wrap. NOTE: Installation instructions supplied with each kit
Specifications
Category Name
Common
Sale Type
New
Manufacturer
SPX